Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't ignore the forklift at the office. If the operation is bad, there will be serious crashes in mins, and there are many mishaps entailing forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's sight, and the individual in front could not be found, causing a rolling crash.
Case 2: In order to maintain the equilibrium of the forklift when lifting heavy products, the employees used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift cargo surpasses the permitted width of the course and hangs on the roadside shelf, which nearly causes an accident.
Instance 4: Forklift is speeding and surrender during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees illegally, the forklift vehicle driver does not put on the safety belt, the forklift lifter falls and the chauffeur is crushed when the forklift rolls over.
Instance 7: The forklift driver did not wear a safety belt and dropped from the car when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after confirming that there are no challenges that hinder the safety of driving, beep the horn initially and afterwards start.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge have to be risk-free before starting.
3. When the forklift starts with a tons, the motorist needs to first verify that the load is steady and reliable.
4. The start has to be slow-moving and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork should not be raised too high, which will certainly influence the security of the forklift. .
3. After unloading, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be released first. High-speed doglegs are banned. High-speed sharp turns will trigger the vehicle to shed lateral security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is restricted to brake instantly while driving with tons unless there are special situations.
6. When the forklift is running, it needs to follow the web traffic rules in the manufacturing facility and need to maintain a certain safety and security range from the vehicle ahead. .
7. When the forklift is running, the load should be in the most affordable setting that does not prevent the driving, and the gantry needs to be correctly slanted back. The lots shall not be raised except when stacking or loading. .
8. The height of the lots should not obstruct the motorist's view. In special scenarios, when the item influences the forward vision, drive at a reduced speed when turning around.
9. It is restricted to turn on the ramp, neither to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it needs to drive safely at a low speed when going into the production workshop location. .
11. When the forklift is raised, raised or driven, it is forbidden for employees to base on the fork to hold items and play a balancing function. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will never run with ailments or conceal them.

filling and unloading.
1. When fork-loading things, the distance between the two forks should be adjusted as required to make the lots of both forks well balanced and not skewed, and one side of the thing must protest the shelf. .
2. It is forbidden to deal with a single fork or utilize a fork top or pull. In unique conditions, security warning signs need to be set up to advise bordering pedestrians. .
3. In the process of filling and discharging things, the forklift should be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt individuals. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the tons, and it needs to be noted that the fork tip need to not touch other goods or items. The tons needs to be stabilized with minimal back tilt of the gantry to make sure that the lots does not slide in reverse. The mast can be slanted forward somewhat when the load is lowered to permit easy placement of the lots and extraction of the forks. .
6. It is prohibited to fork goods at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Overwhelming is forbidden, and it is banned to utilize forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude falling mishaps. .
9. It is not allowed to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to make use of forks to choose, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you should dump the goods or lower the fork structure.
2. Pull the hand brake deal with to dead or dispirit the parking brake switch.
3. The engine is switched off and the power is cut off. (Except for special circumstances, such as the driver does not leave the lorry's view and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance must be checked, and fuel, lubing oil and cooling water should be included.
2. Inspect the safety efficiency of beginning, running and stopping.
3. Check whether the lights and horn signals are complete and reliable.
4. During the operation of the forklift, examine whether the stress and temperature level are typical.
5. After the forklift is running, the outside leak needs to additionally be inspected and the seals should be replaced in time.

Forklift Safety Operation Specifications.
1. You need to check before leaving the cars and truck;.
2. When you experience somebody in front of you during driving, you ought to send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the nadir of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be as well sharp to avoid the propensity of " totally free switching";.
6. Adding and down the slope ought to be slow and consistent, and no turning on the slope is enabled.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the vehicle should be driven in reverse when declining;.
8. When the forklift employees carry the goods and move forward, if they experience huge or hefty goods and most likely to the driver's view, they should take the turning around exercise
.
The "Eight Prohibitions" ought to be adhered to in the procedure.
1. Single fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize braking pressure to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is strictly restricted to stand under the Electric Forklift Truck for Warehouse fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the list below problems.
1. Curves, Electric Forklift Truck for Warehouse slim roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the very same size as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844